| Type: Configuration | Model | Description | Typical Specifications | Key Features |
|---|---|---|---|---|
| Hermetically Sealed Sliding Door: Manual Single Leaf | DR H2SD MSL | Manually operated single-panel sliding door with hermetic seal for OTs and cleanrooms. | Size: 1200 x 2100 mm Leaf: Single Material: SS / HPL / Powder-coated GI Seal: Bottom + perimeter Opening: Manual push-pull |
– Smooth manual glide – Full hermetic sealing – Easy maintenance – Ideal for small OTs |
| Hermetically Sealed Sliding Door: Automatic Single-Leaf | DR H2SD ASL | Automated sliding door with sensor-based motion and full perimeter seal for infection control zones. | Drive: Microprocessor-controlled Size: 1200 x 2100 mm Opening Speed: 250–500 mm/sec Sensors: Infrared / microwave Power: 230V AC |
– Touchless operation – Hermetically sealed – Anti-crush safety – Silent motor |
| Hermetically Sealed Sliding Door: Automatic Double-Leaf | DR H2SD ADL | Wide-opening automatic dual-leaf sliding door for gurney and equipment movement. | Leaf Size: 2 x 1200 mm Total Opening: 2400 mm Material: SS304 / HPL Motor: Belt drive Sensors: Dual-zone presence sensor |
– Large clear opening – Double leaf automation – Medical-grade surface – Optional battery backup |
| Hermetically Sealed Sliding Door: Lead-Lined Radiation Proof | DR H2SD L2RF | Radiation-shielding sliding door for imaging/OT rooms with hermetic sealing. | Shielding: 2 mm Pb equivalence Leaf: SS/Lead/HPL composite Seal: 3-side hermetic Automation: Optional |
– X-ray/MRI compatible – Anti-radiation core – Smooth, quiet operation |
| Hermetically Sealed Sliding Door: Glass Panel with SS Frame | DR H2SD SPS | Transparent hermetic door with clear toughened glass for visibility between zones. | Glass: 10–12 mm toughened Frame: SS 304 Size: 1500 x 2100 mm Seal: Bottom drop seal Motor: Optional |
– Modern aesthetic – Visual access – Hermetic bottom seal – Cleanroom compliant |
| Hermetically Sealed Sliding Door: ICU/Isolation Room Bi-Parting | DR H2SD I2R2P | Bi-parting auto door system for ICU and isolation wards with negative pressure sealing. | Leaf Size: 2 x 1000 mm Motor: Low-noise linear motor Controls: Touchless switch Finish: Antibacterial HPL or SS |
– Suited for ICU/clean zones – Pressure integrity – Hands-free access |
| Hermetically Sealed Sliding Door: Fire Rated with Hermetic Seal | DR H2SD FRS | Sliding door certified for fire safety and hermetic sealing up to 60 minutes. | Fire Rating: EI60 Seal: Intumescent + hermetic Core: Rockwool + GI Automation: Available |
– Fire-resistant – Sealed for smoke/gas – Fire-rated glazing optional |
Access control (RFID, keypad, facial recognition)
Battery backup for motor
Touchless sensors and foot switches
Door status indicator lights (Red/Green)
Vision panels or X-ray safe glass
Cleanroom-rated antibacterial coatings
| Type | Model | Description | Specifications | Features |
|---|---|---|---|---|
| PLA | DR HTB PLA 1.75 | Biodegradable thermoplastic derived from renewable resources. | Diameter: 1.75mm ±0.03mm Temp: 180–210°C Bed: 0–60°C |
– Easy to print – Low warping – Great surface finish – Minimal odor |
| PLA | DR HTB PLA3 | Same as above but with 3.00mm filament diameter. | Diameter: 3.00mm ±0.03mm Temp: 180–210°C Bed: 0–60°C |
– For 3.00mm extruders – Eco-friendly – Consistent extrusion |
| ABS | DR HTB ABS1.75 | Petroleum-based plastic with strong, durable properties. | Diameter: 1.75mm ±0.03mm Temp: 210–240°C Bed: 80–110°C |
– High strength – Heat resistant – Slightly flexible |
| PETG | DR HTB PETG1.75 | Strong and flexible like ABS, but easier to print. | Diameter: 1.75mm ±0.03mm Temp: 230–250°C Bed: 70–90°C |
– Durable and tough – Water resistant – Glossy finish |
| Wood PLA | DR HTB WFPLA | PLA infused with fine wood particles for a wood-like finish. | Diameter: 1.75mm ±0.03mm Temp: 190–220°C Bed: 0–60°C |
– Wood grain texture – Sandable and stainable – Natural appearance |
| Glow in the Dark PLA | DR HTB GPLA | PLA that glows after absorbing light. | Diameter: 1.75mm ±0.03mm Temp: 190–220°C Bed: 0–60°C |
– Emits glow in dark – Good layer adhesion – Fun for decorative items |
| Flexible TPU | DR HTB TPU1.75 | Flexible thermoplastic polyurethane for elastic parts. | Diameter: 1.75mm ±0.05mm Temp: 200–230°C Bed: 40–60°C |
– High flexibility – Impact and abrasion resistant – Smooth extrusion |
| Silk PLA | DR HTB SPLA | PLA with silky, shiny finish. Ideal for aesthetic prints. | Diameter: 1.75mm ±0.03mm Temp: 190–220°C Bed: 0–60°C |
– Metallic sheen – High visual impact – No post-processing needed |
| Carbon Fiber PLA | DR HTB CPLA | PLA reinforced with carbon fibers for extra strength. | Diameter: 1.75mm ±0.03mm Temp: 200–230°C Bed: 50–60°C |
– Lightweight – Stiff and strong – Matte finish |
| Metal PLA | DR HTB BCPLA | PLA blended with metal powder for heavy, metallic prints. | Diameter: 1.75mm ±0.03mm Temp: 195–220°C Bed: 0–60°C |
– Metallic appearance – Polishable – Heavier than standard PLA |
©2025-26. All Rights Reserved. Shresha Biortek PVT LTD
